Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Akinodal Moshura
Country: Somalia
Language: English (Spanish)
Genre: Video
Published (Last): 12 May 2015
Pages: 311
PDF File Size: 7.5 Mb
ePub File Size: 13.36 Mb
ISBN: 250-6-15760-402-2
Downloads: 25927
Price: Free* [*Free Regsitration Required]
Uploader: Zolosida

Bottom side of the circuit board: A message is always formed like this: By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Intelligent contol panels I found hormamn guidewhich made the setup easier and I’ve setup everything accordingly. The description in the patents is not cristal clear at least to me but still extremely helpful in figureing out whats going on on the bus.

Hörmann Universaladapterplatine UAP 1 | Smolka Tor- und Antriebstechnik Berlin Online Shop

Burglar alarm As you can see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me. Exactly what I want to have: To change the partial opening position: To dig deaper into the protocoll I need more data. Hardware Top side of the circuit board: Currently I send a 0. The slave responds to a status request by the master.

Email Required, but never shown.

This is how far i got until now. Fortunately the page gives you a nice lookup table for the CRC values which I then used in my Python program to verify all the messages I’ve recorded so far.


I hoped to find the signals there as well but it turned out that is not the case. Unfortunately the patent doesn’t say anything about the device codes. So I basically want a remotely controlled button the app where I click open and it will start moving up until the end position, which should be possible, and it sometimes does move or open, but something must be off with the connection, horrmann duration or voltage as it does not work consistently: These are the messages I was able to make sense of so far.

Bus scan At startup the Master scans the bus for devices. Dominik Hadl 51 4. This question came from our site for electronics and electrical engineering professionals, students, and enthusiasts.

Reverse engeneering the Hörmann UAP1 protocoll

The changed partial opening position is saved. Press the PRG button until the decimal point next to the menu number is illuminated. Looking at the other link for the Hormann website using translation – it looks like they indicate it can do a partial open: That way I’m able to trace the bus in realtime without the need to leave the house It’s pretty cold outside at this time of the year. I hormanj an electronics amateur and can’t figure out based on the schematic below if that is correct?

Reverse engeneering the Hörmann UAP1 protocoll

Top side of the circuit board: If the selected height is too low, a 2-digit number starting with 1 will appear with a flashing decimal point see section By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.


That being said you might be hormznn to program a button to activate open when pressed and to also activate the same function on release. Not much to see here, just that all pins of the 6-pin RJ12 sockets are directly conected to each other. I’ve set two analyzers for async serial data on both, the RX and the TX line. Hotmann searched the internet horrmann information about the bus, but little to nothing can be found about it.

As you can see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me. The CRC hormqnn After being able to seperate the byte stream into messages, I still wasn’t able to calculate the checksum. Home Questions Tags Users Unanswered. Sign up using Email and Password.

The message can be between 1 and 3 bytes long and the uqp1 states that it can be expanded. Why it doesnt scan the adresses down to ? Address Ranges The patent gives a list of adresses for certain device categories: RX When the board is powered while the logic analyzer is collecting data, we see these bytes comming in:

Author: admin